Hi, Fashionistas!

I wanted to share a sewing project with you that I made for Easter but never blogged about it. Here is the dress I made. The bodice is Mccalls M6886 and the skirt is self drafted. I’ll show you how below:

I wanted to make something with stripes. Stripes are so chic and never go out of style. I chose to make a dress with a scoop neck, fitted bodice, three-quarter sleeve and a pleated skirt. For the bodice, I chose McCalls M6886, mainly because the pattern is something I have in my stash and I use often. I can also cut the size I need straight out of the envelope, and it does not need any alterations. You can use any bodice from your pattern stash!

At first, I kept the bodice the same length as this top I made previously. It hits at about the low hip and would let me decide the positioning of my waist seam at a later time.

Once I had the bodice sewn up, and moved on to making the skirt, I measured the bodice from the neckline along the center front.

I typically like my waist seam to fall on the natural waist, which is the smallest part of the torso. Then I marked the waist seam and chopped off the bodice excess after marking my 5/8 inch seam allowance.

Next, it was time to move on to the skirt, and do a small amount of math (nothing super technical) to determine the placement and size of the pleats.

While this is not a fixed formula, I want to share my thought process that you can use to create your own version of this dress!

Here is what I did next, I took a flat measurement of the waist on the bodice. This was 14 inches, excluding seam allowances

Then I took my fabric and folded selvage to selvage. Next, I decided how long I wanted the skirt to be. For me, that was 19 inches. To this, I added measurements of 5/8 inch on top for seam allowance and 1 inch on the bottom for hem allowance. I used this final measurement to cut the fabric to where it looked like this:

Now I took a flat measurement of the folded fabric across the top. This was 32 inches, excluding seam allowance. I then cut the fabric into 2 pieces by cutting the fold. This gave me a skirt front of 32 inches and a skirt back of 32 inches.

Now my goal was to create some pleats on the skirt pieces so that 32 inches would match closely to the 14 inches. For this, I did some simple math and I find that easier to demonstrate on paper. The 1st thing you need to do is decide the placement of the inverted box pleats on your bodice. To do this, I took my bodice and pinned the center front, shown in green on the diagram below (point A). I wanted the placement of the inverted box pleats to fall on my princess seam. For me, that is 3 inches from the center front. So I pinned points B and C on my bodice. The measurement of AB and AC are 3 inches each. When the skirt is attached to the bodice, the inverted box pleats will con-inside with points B and C shown on the bodice in the diagram below

Now that you have placed your pins, you can set the bodice aside. You can also make notches at these points if you prefer.

Now let’s move on to the skirt! I will demonstrate the sewing on a small piece of muslin, that mimics the shape of the skirt on a miniature scale. This will make it easy to demonstrate how I marked and constructed the inverted box pleats.

Because the bodice is 14 inches and the skirt is 32 inches, let us take the difference of the two measurements to decide how much excess we need to eat up in the form of inverted box pleats. 32 minus 12 is 18 inches. Since we are adding 2 invested box pleats, placed at each princess seam, we need each invested box pleat to eat up 9 inches each (18 divided by 2). Make sense so far?

This is all the math you will need to do, now we can do some markings on the skirt and then we are ready to baste the pleats in place! I am showing you the markings on paper below, then we will move on to a sample of sewing the inverted box pleats on muslin! Let’s go over the markings on the diagram below. A is the center of the fabric. AB and AC are 3 inches from the center of the fabric. This is done so that the pleats will coincide with the princess seams on the bodice. Now the final marking is going to be 9 inches from points B and C. This is because we decided that the excess each pleat needs to eat up 9 inches. Measurements BE and CD are 9 inches each. This is all you have to mark on the skirt. You would use pins to mark as I did, or you can make notches in your fabric, whatever you prefer.

Now let us move on to the final step in this pictorial, which is the constructions of the inverted box pleats! By definition, an inverted box pleat is two pleats that are facing each other. If you have never sewn inverted box pleat before, I will show you in muslin below.

On the muslin below, I have marked points A,B,C,D and E.

Now for the construction of the 1st inverted box pleat. pick up the fabric at point D, and place it on top of point C. now make a small stitch as shown to secure the pleat down. This stitch is usually 1/2 inch long.

I have highighted the stich in orange below:

Flip the fabric such that the wrong side is facing up. Now we are ready to flatten the area between C and D and create our inverted box pleats. You can now finger press the excess down on the wrong side of the fabric and distribute it evenly on both sides. now press this down into place.

Now pin this down. You have successfully created the 1st inverted box pleat! Now do the same on the other side of the skirt using points E and D. When you are done, Secure the pleats down by using a basting stitch 1/4 inch from the edge of the fabric. At this point, your skirt front should look like this:

next steps in construction are as follows:

- Create pleats on the skirt back using the same method.
- Sew up the side seams
- Attach the skirt to bodice matching up the center front, center back, side seams and make sure the points B and C on the bodice match the points B and C on the skirt!
- Hem the garment

This is it! I inserted pockets in my dress, in which case, you would want to add the pockets before step 2!

Here are some more pictures of my dress.

I styled my dress with a black belt and black open toe pumps. This ensemble is perfect for summer!

I hope you enjoyed reading this and this encouraged you to try some free handing of your own! While I like using patterns, I also like being independent of them. Many times I run into accidental inventions and those are the best!

XOXO

-Vatsla 🙂

Cuteness!!!

Thanks Alethia!

Such a great dress with a gorgeous fabric choice and fit!

Thanks Sue!

Very cute!

Thanks Gayle!

I suck at math but I do like this!! I have done a pleated skirt before, but never know how big I should make my pleats for my size…small pleats vs big pleats is the question, can you provide an insight?

Hi La-Kia! Personally I like bigger pleats. They are more defined and make a statement. If you want your pleats to be the focal point, then go for deep pleats! Most times since I am free handing, I juts try the pleat and step back and see how I feel about them. Others times I am at the mercy of the width of the fabric, and just make it work, like I did here!

Hope that helps!

Love it!

Thanks JeTua!

Thank You, this is an awesome tutorial. I finally found something that can help me. Thanks for sharing!