Tag: pattern making tutorial

Pattern Making Tutorial: How to Draft an all in one facing

Hi, Fashionistas!

I wanted to share a recent sewing project with you and show you how to draft all in once facings for patterns that don’t have one included. Drafting small pattern like these are a great way to get familiar with pattern making!

Here is the dress I made. I drafted the all in one facing using the steps outlined in this tutorial.

You may have noticed that most times commercial patterns have separate neck facings and separate arm facings. I prefer all in one facing because they allow you to clean finish your neckline and armholes on a sleeveless garment in one go. They look professional as well.

Before we get started drafting, let’s have a look at the front of the all in one facing. Here is what my front facing looks like after I cut it out:

Here is an example of what my back facings looked like. The center back seams on this picture are overlapping, however, there is a center back opening on this pattern that allows for a back zipper:

Now that we have had a look at the garment and the facing that lies underneath, let’s jump into the tutorial! I will be showing you this method using a miniature pattern. I’ll demonstrate with the front bodice pattern

Step 1: Cut out your bodice pattern. If you have a dart that falls on the shoulder seam or a french dart that falls close to the armhole, shut it close using tape.

Step 2: Keeping the original pattern as flat as possible, trace around the side seam, armhole, shoulder, and neckline and center front. In order to keep your original pattern flat, you can place weights or pin the pattern down on top of pattern paper.  Your traced pattern should look something like this.

Step 3: Next we need to freehand the shape of the bottom of the facing. In order to do this. measure down 3 inches on the center front, and about 2 inches on the side seam, and connect the two using a shape as shown below.If you have a french curve, you can use that to draw such shapes, but free handing works as well!

Step 4 : Copy all the markings from your original pattern to your facing pattern. For example, here I have shown the grain line, fold, CF  for center front. I have also added the name of the pattern piece, which is “front facing” and indicated how many pieces to cut, which is my case is “Cut 1 on fold”

If you were to lay your newly drafted facing pattern on top of the original pattern, it should match

The steps to draft the back facing are exactly the same. Here is what the back facing looks like:

Step 5: Make sure the side seams on the front facing and back facing match up and you will be sewing these up. This step is called “Truing”

<Insert pic here>

A few things to note about facings. Facings do not contain darts, or princess seams. If your pattern has darts, tape them shut as shown above in the pictorial. If your pattern has princess seams, you would tape the princess seams together overlapping the seam allowance.

I hope that you found this tutorial helpful and that you will try your hand at some pattern making!

XOXO

-Vatsla 🙂

Pattern Making using Painters Tape!

I recently saw this on pinterest I believe, and was curious. I have created some patterns from RTW, but I usually use a method that requires poking several sewing pins into the garment along the seams lines.  I was wanting to sew yesterday but didn’t have a pattern for jeans so decided to give this method a try! See below for step by step instructions on how. Let me start by saying that I work out of my kitchen. I pattern make on the kitchen island and sew in our music room. So if you see any tomatoes, melons, pots and pans in the background, please excuse them. I promised them their five seconds of fame 🙂

So this is a very basic method. Not technical at all. You grab a roll of painters tape and create an outline for each individual pattern piece. To create the outline, I tore off small pieces of painters tape and placed them on the stitch line or seams. The image below if of the front leg. My aim here is to flatten the front leg and paste the tape on it, such that I can get a one-dimensional rub off of the leg.

IMG_8071

Next, I filled in the outline with more painters tape:IMG_8072

 

 

Once this was done, I was able to peel off the tape, and it came off as one big chunk. I then placed it on pattern paper and made sure it was flat.  Next, I used this nifty measuring gauge to add a half-inch seam allowance all around. The dotted line became the outline of my pattern piece for the front leg and I used the dotted line as a guide to cut out the pattern. IMG_8074

This is what the pattern looked like after cutting it. Say hi to Poochie!!!IMG_8080

And my kid wanted to make an appearance as well. Love this little stinker..IMG_8083

You can leave the tape on if you like, but I pulled it off and added a grainline, name of the pattern, and how many to cut. I added an awl punch at the crotch. I didn’t care to add notches, but typically I would. This pattern is so simple that I did not bother. IMG_8087

That’s it! That’s all you have to do to create a pattern. Repeat this step for all patterns pieces on your garment and you can replicate your favourite garment over and over again.

Now the back I did slightly different because the pant leg on the back is usually wider than the front leg as you can see below.

IMG_8088

To overcome this , I first taped just like I did the front leg. I re-used the tape from the front because I hate wasting and killing the environment, so I try my best to re-use. I was not too careful about taping at first. Then I went in with a pen and outlined along the stitch line to get the accurate shape.IMG_8091

This is what the back looked like when I was done with the portion of the back leg that sat flat. I still had to tackle the part of the back leg that extends beyond the side crease to the side seam.IMG_8096

For this I flattened the pant leg, allowing me to tape all the way to the side seam. My finger is pointing to where the side crease was . That’s it! IMG_8097

I did the same with the back yoke, waist band and pocket. I also tried drafting the pocket but it was not as accurate as using painters tape. IMG_8098

Here is the waist band. It’s a contoured waist band as this is a low-rise pair of jeans. Be sure to make CF and CB on the waist band as the waist band has an extension and this can be confusing while sewing. I also recommend using notches to match up the Centre Front, Centre Back, and side seams.IMG_8100

If you liked this tutorial, check out the rest of my tutorials HERE

The one thing I have to figure out is adding the front facing fly before I can cut. To make things super simple, I am going to go with a mock fly zipper and use this pattern as a base.

I am hoping to finish the pattern today and then cut and sew hopefully tomorrow. I would be beyond excited if I can get this completed this week. I know there are some amazing sewing divas out there that pop out a new garment every other day,  but I have to be realistic about my sewing goals, given all my other commitments.

Anyhooz- tell me what you think about this method. Have you used it? If so, do you love it? Or do you have another preferred method? I prefer this over cutting up the garment. It wastes tape, but its more green than cutting up the garment and wasting it. There are so many poor people in this world that could use old clothes, so I really don’t want to destroy any garments.  I’ll be back with my white skinnies soon .Send me some sewing motivation <3

 

Update: I made my skinny jeans using this method and you can see there HERE

-XOXO

-Vatsla.

 

%d bloggers like this: